after Qi no USB in Nor questions

[C R McClenaghan]

All,

I have a Neo Freerunner GTA02V5 to which I apparently flashed Qi some  
weeks ago. I'm not sure which version of FSO is flashed to memory, but  
I think it is milestone 3. In installing Qi, I think I may have been  
trying to recover from modifications made to uboot for Debian and  
probably ran the devirginator process to flash uboot before I went  
ahead and flashed Qi. I no longer recall why I did either.

And now, I'm a little confused as to how to proceed as I can no longer  
flash with dfu-util. When I boot to Nor and plug in the USB cable, I  
get a series of errors on my host and cannot use dfu-util. The errors  
are these:

[   87.928631] usb 1-1: new full speed USB device using uhci_hcd and  
address 3
[   88.540254] usb 1-1: unable to read config index 0 descriptor/ 
start: -71
[   88.540437] usb 1-1: chopping to 0 config(s)
[   88.695904] usb 1-1: string descriptor 0 read error: -71
[   88.698093] usb 1-1: string descriptor 0 read error: -71
[   88.700419] usb 1-1: string descriptor 0 read error: -71
[   88.734000] usb 1-1: no configuration chosen from 0 choices
[   88.736092] usb 1-1: USB disconnect, address 3
[   89.084376] usb 1-1: new full speed USB device using uhci_hcd and  
address 4
[   89.692859] usb 1-1: invalid descriptor for config index 1: type =  
0x2, length = 0
[   89.692909] usb 1-1: can't read configurations, error -22
[   89.912237] usb 1-1: new full speed USB device using uhci_hcd and  
address 5
[   90.420975] usb 1-1: invalid descriptor for config index 1: type =  
0x2, length = 0
[   90.421000] usb 1-1: can't read configurations, error -22
[   90.641355] usb 1-1: new full speed USB device using uhci_hcd and  
address 6
[   90.676829] usb 1-1: invalid descriptor for config index 1: type =  
0x2, length = 0
[   90.676850] usb 1-1: can't read configurations, error -22
[   90.900242] usb 1-1: new full speed USB device using uhci_hcd and  
address 7
[   90.939088] usb 1-1: invalid descriptor for config index 1: type =  
0x2, length = 0
[   90.939111] usb 1-1: can't read configurations, error -22
[   90.940610] hub 1-0:1.0: unable to enumerate USB device on port 1

This occurs whether the Freerunner is attached to the host first or not.

Note: when booted into installed image, USB networking is fine and the  
above errors do not occur. Is this a host side problem or Neo  
Freerunner problem?

I notice in the Qi documentation that there is no dfu-util support.  
Would that effect dfu-util in Nor?

When I do attempt to boot into Nand, I end up with a Nor boot menu  
that is the same as when I boot into Nor - apparently either why the  
AUX/Power button are selected I boot to Nor. Is that correct behavior  
with Qi?

BTW - my Nor boot menu seems slightly different than what I see on the  
wiki - rather than a Reset option in the fifth position I have Reboot.

Are there any log or configuration files I should post to help  
diagnosis?

I would like to be able to upgrade the release in memory or for that  
matter Qi - which I think I'm now blocked from doing.

Is there an alternative to the "devirginator" process to restore the  
Freerunner to "factory" state?

Thanks,

Chris