<div dir="ltr">Hey All,<br><br>I was wondering if anyone was using the Neo1973 (GTA01v4) with Debug board v3. I used the openocd.cfg available on the wiki and I get this problem:<br>Info: openocd.c:82 main(): Open On-Chip Debugger (2006-08-01 12:00 CEST)<br>
Info: configuration.c:50 configuration_output_handler(): Command ft2232_device_desc not found<br>Info: configuration.c:50 configuration_output_handler(): Command ft2232_layout not found<br>Info: configuration.c:50 configuration_output_handler(): Command ft2232_vid_pid not found<br>
Error: jtag.c:1219 jtag_init(): No valid jtag interface found (ft2232)<br><br>It seems like openocd is having some trouble with ft2232 because I don't see anything wrong with those commands. <br><br>lsusb shows that the debug board is connected:<br>
Bus 003 Device 003: ID 1457:5118 <br>Device Descriptor:<br> bLength 18<br> bDescriptorType 1<br> bcdUSB 2.00<br> bDeviceClass 0 (Defined at Interface level)<br> bDeviceSubClass 0 <br>
bDeviceProtocol 0 <br> bMaxPacketSize0 8<br> idVendor 0x1457 <br> idProduct 0x5118 <br> bcdDevice 5.00<br> iManufacturer 1 OpenMoko<br> iProduct 2 Debug Board for Neo1973<br>
iSerial 0 <br> bNumConfigurations 1<br> Configuration Descriptor:<br> bLength 9<br> bDescriptorType 2<br> wTotalLength 55<br> bNumInterfaces 2<br>
bConfigurationValue 1<br> iConfiguration 0 <br> bmAttributes 0x80<br> (Bus Powered)<br> MaxPower 100mA<br> Interface Descriptor:<br> bLength 9<br>
bDescriptorType 4<br> bInterfaceNumber 0<br> bAlternateSetting 0<br> bNumEndpoints 2<br> bInterfaceClass 255 Vendor Specific Class<br> bInterfaceSubClass 255 Vendor Specific Subclass<br>
bInterfaceProtocol 255 Vendor Specific Protocol<br> iInterface 2 Debug Board for Neo1973<br> Endpoint Descriptor:<br> bLength 7<br> bDescriptorType 5<br>
bEndpointAddress 0x81 EP 1 IN<br> bmAttributes 2<br> Transfer Type Bulk<br> Synch Type None<br> Usage Type Data<br> wMaxPacketSize 0x0040 1x 64 bytes<br>
bInterval 0<br> Endpoint Descriptor:<br> bLength 7<br> bDescriptorType 5<br> bEndpointAddress 0x02 EP 2 OUT<br> bmAttributes 2<br>
Transfer Type Bulk<br> Synch Type None<br> Usage Type Data<br> wMaxPacketSize 0x0040 1x 64 bytes<br> bInterval 0<br> Interface Descriptor:<br>
bLength 9<br> bDescriptorType 4<br> bInterfaceNumber 1<br> bAlternateSetting 0<br> bNumEndpoints 2<br> bInterfaceClass 255 Vendor Specific Class<br>
bInterfaceSubClass 255 Vendor Specific Subclass<br> bInterfaceProtocol 255 Vendor Specific Protocol<br> iInterface 2 Debug Board for Neo1973<br> Endpoint Descriptor:<br> bLength 7<br>
bDescriptorType 5<br> bEndpointAddress 0x83 EP 3 IN<br> bmAttributes 2<br> Transfer Type Bulk<br> Synch Type None<br> Usage Type Data<br>
wMaxPacketSize 0x0040 1x 64 bytes<br> bInterval 0<br> Endpoint Descriptor:<br> bLength 7<br> bDescriptorType 5<br> bEndpointAddress 0x04 EP 4 OUT<br>
bmAttributes 2<br> Transfer Type Bulk<br> Synch Type None<br> Usage Type Data<br> wMaxPacketSize 0x0040 1x 64 bytes<br> bInterval 0<br>
Device Status: 0x0000<br> (Bus Powered)<br><br>Any ideas? Thanks!<br><br>Lynn<br></div>