<div dir="ltr">Why would I want to do that to the debug board? <a href="http://wiki.openmoko.org/wiki/Debug_Board_v3">http://wiki.openmoko.org/wiki/Debug_Board_v3</a> . If the usb id is <br>0403:6010 then its wrong isn&#39;t it?<br>
<br>Also I don&#39;t understand this section of the wiki page:<br><a href="http://wiki.openmoko.org/wiki/OpenOCD#Known_Bugs_and_Troubleshooting">http://wiki.openmoko.org/wiki/OpenOCD#Known_Bugs_and_Troubleshooting</a><br>
<br><blockquote><h3> <span class="mw-headline"> Did you turn it on&nbsp;? </span></h3><p>An easily made but devastating mistake is to forget to actually activate the CPU. Just connecting power is not enough&nbsp;!
Press and hold the power button until the boot loader does its count-down, or, in case there is no runnable boot loader,
the CPU keeps itself busy.
</p></blockquote>
is the &#39;it&#39; this part referring to the openmoko? I mean, isn&#39;t the whole point of a bricked openmoko the fact that it can&#39;t turn on? How am I supposed to activate the CPU if it won&#39;t turn on at all? I know the battery is fully charged because I checked the voltage.<br>
<br>this is the openocd.cfg i am using:<br><br><blockquote>telnet port 4444<br>gdb_port 3333<br><br># interface<br>interface ft2232<br>jtag_speed 8<br>ft2232_device_desc &quot;Debug Board for Neo1973&quot;<br>ft2232_layout &quot;jtagkey&quot;<br>
ft2232_vid_pid 0x1457 0x5118<br>reset_config trst_and_srst<br>jtag_device 4 0x1 0xf 0xe<br>daemon_startup attach<br>target arm920t little reset_run 0 arm920t<br>working_area 0 0x200000 0x4000 backup<br>run_and_halt_time 0 5000<br>
</blockquote>How do I check my debug board&#39;s uart console? I can&#39;t remember how to do it but I&#39;m pretty sure I was able to screen onto it once.<br>&nbsp;<br>Actually maybe it is something with my debug board, I looked in the logs and saw this:<br>
<blockquote>[&nbsp; 459.596147] usb 3-1.3: new full speed USB device using uhci_hcd and address 27<br>[&nbsp; 459.744465] usb 3-1.3: device not accepting address 27, error -71<br></blockquote>Do you know what to make of this error? Google search finds nothing =/.<br>
<br>Lynn<br><div class="gmail_quote">On Mon, Sep 1, 2008 at 12:43 AM, Neng-Yu Tu (Tony Tu) <span dir="ltr">&lt;<a href="mailto:tony@openmoko.com">tony@openmoko.com</a>&gt;</span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div class="Ih2E3d">-----BEGIN PGP SIGNED MESSAGE-----<br>
Hash: SHA1<br>
<br>
Hi Lynn-<br>
<br>
</div>Lynn Nguyen ??:<br>
<div class="Ih2E3d">&gt; Yeah it&#39;s loading the correct openocd.cfg file. I even added random<br>
&gt; commands to it and i saw those commands in the error messages. I even<br>
&gt; used -f to be sure.<br>
&gt;<br>
<br>
<br>
</div>* Could you check the .cfg file is comes with, it should called<br>
openocd-debugv2.cfg :<br>
<br>
1. ft2232_vid_pid 0x1457 0x5118<br>
<br>
2. And adjust jtag_speed to higher number (4 or 8, default is 0)<br>
<br>
* And is your debug board UART (terminal console) is working?<br>
<br>
If still not working, you might could erase the EEPROM content in the<br>
debug board again, return the default USB ID 0403 6010. They see if the<br>
UART and openocd could work.<br>
<br>
Regards,<br>
<div><div></div><div class="Wj3C7c"><br>
- --<br>
Neng-Yu Tu (Tony Tu)<br>
Openmoko, Inc.<br>
Support.<br>
<br>
Some questions could be answered by reference following link:<br>
<br>
Wiki - <a href="http://wiki.openmoko.org" target="_blank">http://wiki.openmoko.org</a><br>
Download - <a href="http://downloads.openmoko.org" target="_blank">http://downloads.openmoko.org</a><br>
<br>
Freerunner Introduction -<br>
<a href="http://wiki.openmoko.org/wiki/Getting_Started_with_your_Neo_FreeRunner" target="_blank">http://wiki.openmoko.org/wiki/Getting_Started_with_your_Neo_FreeRunner</a><br>
<br>
<br>
<br>
&gt;&gt; I was wondering if anyone was using the Neo1973 (GTA01v4) with Debug<br>
&gt;&gt; board v3. I used the openocd.cfg available on the wiki and I get this<br>
&gt;&gt; problem:<br>
&gt;&gt; Info: &nbsp; &nbsp;openocd.c:82 main(): Open On-Chip Debugger (2006-08-01<br>
&gt; 12:00 CEST)<br>
&gt;&gt; Info: &nbsp; &nbsp;configuration.c:50 configuration_output_handler(): Command<br>
&gt;&gt; ft2232_device_desc not found<br>
&gt;&gt; Info: &nbsp; &nbsp;configuration.c:50 configuration_output_handler(): Command<br>
&gt;&gt; ft2232_layout not found<br>
&gt;&gt; Info: &nbsp; &nbsp;configuration.c:50 configuration_output_handler(): Command<br>
&gt;&gt; ft2232_vid_pid not found<br>
&gt;&gt; Error: &nbsp; jtag.c:1219 jtag_init(): No valid jtag interface found<br>
&gt; (ft2232)<br>
&gt;<br>
&gt;&gt; It seems like openocd is having some trouble with ft2232 because I<br>
&gt; don&#39;t<br>
&gt;&gt; see anything wrong with those commands.<br>
&gt;<br>
&gt;<br>
&gt; Does your openocd load neo1973 specific config? like tmp/openocd -f<br>
&gt; tmp/openocd-debugv2.cfg<br>
&gt;<br>
&gt; Usually it is because your USB vid/pid setting is not correct in the<br>
&gt; config file(load the wrong config file)<br>
&gt;<br>
&gt; Hope this helps.<br>
&gt;<br>
<br>
</div></div><div class="Ih2E3d">-----BEGIN PGP SIGNATURE-----<br>
Version: GnuPG v1.4.9 (MingW32)<br>
Comment: Using GnuPG with Mozilla - <a href="http://enigmail.mozdev.org" target="_blank">http://enigmail.mozdev.org</a><br>
<br>
</div>iEYEARECAAYFAki7nRcACgkQmV6sZhhBn2/jIACgjEh/KVZXXdhD4sLyZh17d9gA<br>
DG4AnAmOZwoBDKSqNn3mua2WQnvi9xCp<br>
=wz/W<br>
<div><div></div><div class="Wj3C7c">-----END PGP SIGNATURE-----<br>
<br>
_______________________________________________<br>
Openmoko community mailing list<br>
<a href="mailto:community@lists.openmoko.org">community@lists.openmoko.org</a><br>
<a href="http://lists.openmoko.org/mailman/listinfo/community" target="_blank">http://lists.openmoko.org/mailman/listinfo/community</a><br>
</div></div></blockquote></div><br></div>