<html><head><style type="text/css"><!-- DIV {margin:0px;} --></style></head><body><div style="font-family:verdana, helvetica, sans-serif;font-size:12pt"><DIV></DIV>
<DIV>Hi Joerg, thanks for the reply.&nbsp;</DIV>
<DIV>&nbsp;</DIV>
<DIV>You must have missed this bit (before the first photo)<BR></DIV>
<DIV>&nbsp;&nbsp; "I probed R4303 and found it was 2k2Ω"&nbsp;&nbsp;</DIV>
<DIV>&nbsp;</DIV>
<DIV>my&nbsp;phone was manufactured on 20080821.</DIV>
<DIV>&nbsp;</DIV>
<DIV>&nbsp;</DIV><A href="http://www.fsf.org/register_form?referrer=5006" target=_blank rel=nofollow><IMG height=31 alt="[FSF Associate Member]" src="http://www.geocities.com/aclearn/getButton.png" width=88></A>
<DIV><BR></DIV>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: verdana, helvetica, sans-serif"><BR>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: verdana, helvetica, sans-serif"><FONT face=Tahoma size=2>
<HR SIZE=1>
<B><SPAN style="FONT-WEIGHT: bold">From:</SPAN></B> Joerg Reisenweber &lt;joerg@openmoko.org&gt;<BR><B><SPAN style="FONT-WEIGHT: bold">To:</SPAN></B> hardware@lists.openmoko.org<BR><B><SPAN style="FONT-WEIGHT: bold">Cc:</SPAN></B> Anthony Clearn &lt;aclearn@yahoo.co.uk&gt;; steve@openmoko.com<BR><B><SPAN style="FONT-WEIGHT: bold">Sent:</SPAN></B> Friday, 27 March, 2009 2:34:00<BR><B><SPAN style="FONT-WEIGHT: bold">Subject:</SPAN></B> Re: my buzz fix method<BR></FONT><BR>Am Fr&nbsp; 27. März 2009 schrieb Anthony Clearn:<BR>&gt; Hi,<BR>&gt; Here is my attempt <A href="http://anyotherkey.googlepages.com/c" target=_blank>http://anyotherkey.googlepages.com/c</A><BR>&gt; <BR>&gt; AFAIK I made a few mistakes:<BR>&gt; <BR>&gt; 1 I could have used a smaller sized 100uF cap<BR>&gt; <BR>&gt; 2 I could have used thinner wire, I picked up the wrong spool and didn't <BR>realise <BR>&gt; <BR>&gt; 3 I shouldn't have tried to open a solder bridge on a 0402 component
 with a <BR>relatively large iron.<BR>&gt; <BR>&gt; I'm looking into the low volume of my voice on calls, I've only read up <BR>briefly on what could be the cause. I can't be certadinin it wasn't always so <BR>low! I am looking through the posts to figure this out from other peoples <BR>experiences.<BR><BR>Hey Anthony<BR>muchas gracias for this really cool photo footage. Close to real live. It's <BR>been all the same when I started to try and do that.<BR><BR>Regarding your low volume: did you check R4303? (It's the one below the two NC <BR>pads and right side to C4303, the one you borked and replaced. It's clearly <BR>mentioned in my SOP paper) R4303 is not mentioned in your story if I didn't <BR>miss anything. Usually it's 0R and it's amazing you get *any* signal at all <BR>from mic if you haven't replaced it by a ~2k2k (probably anything between <BR>400Ohms and 3k will do, though I learnt by your report even a 0R will do at <BR>least partially :D&nbsp;
 ).<BR><BR><BR>Please keep on reporting this way, and don't hesitate to ask me for whatever <BR>kinda help you might need. I have a few spare devices for emergencies ;-)<BR>Your report is considered *very* encouraging by me. It shows how much you can <BR>deviate from SOP recommendations and still you get better results than MP <BR>device. Also it shows everybody is encountering some sort of same problems <BR>when doing this first time, and there's a way to recover from those.<BR><BR>a heartly cheers<BR>jOERG<BR></DIV></DIV></div></body></html>