Can't get bluetooth started

[Sean McNeil]

Reset doesn't help either:

echo "1"> /sys/bus/platform/devices/neo1973-pm-bt.0/power_on
echo "1"> /sys/bus/platform/devices/neo1973-pm-bt.0/reset
echo "0"> /sys/bus/platform/devices/neo1973-pm-bt.0/reset
cat /sys/bus/platform/devices/neo1973-pm-bt.0/power_on
1

(at least it seems to say it is powered up now)

but device is not present. I have

CONFIG_BT_HCIUSB=y
CONFIG_BT_HCIUSB_SCO=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_BERRY_CHARGE=y
CONFIG_USB_GADGET_SELECTED=y
CONFIG_USB_GADGET_S3C2410=y
CONFIG_USB_S3C2410=y
CONFIG_USB_ETH=y


Michael Kluge wrote:
> Hi Sean,
>
> as far as I remember it is needed to reset the BT device after 
> powering it up in order to make it functional.
>
>
> Michael
>
>
> Sean McNeil schrieb:
>> I'm not sure why, but I can't get the bluetooth device to start on 
>> GTA02v6 with andy kernel:
>>
>> ...
>> <6>usbcore: registered new interface driver usbfs
>> <6>usbcore: registered new interface driver hub
>> <6>usbcore: registered new device driver usb
>> <6>Bluetooth: Core ver 2.11
>> <6>NET: Registered protocol family 31
>> <6>Bluetooth: HCI device and connection manager initialized
>> <6>Bluetooth: HCI socket layer initialized
>> ...
>> <7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
>> <6>s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
>> <6>s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus 
>> number 1
>> <6>s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
>> <6>usb usb1: configuration #1 chosen from 1 choice
>> <6>hub 1-0:1.0: USB hub found
>> <6>hub 1-0:1.0: 2 ports detected
>> <6>usbcore: registered new interface driver berry_charge
>> <3>s3c2410_udc: debugfs dir creation failed -19
>> <6>s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 
>> 128 bytes
>> <7>gta02_udc_command(2)
>> <4>ether gadget: using random self ethernet address
>> <4>ether gadget: using random host ethernet address
>> <6>usb0: Ethernet Gadget, version: May Day 2005
>> <6>usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk
>> <6>usb0: MAC ba:53:87:a2:2b:75
>> <6>usb0: HOST MAC da:df:99:64:2c:0b
>> <7>gta02_udc_command(1)
>> ...
>> <6>usb0: full speed config #1: 500 mA, Ethernet Gadget, using CDC 
>> Ethernet
>>
>> usb gadget is working. I am nfs mounting filesystem over usb.
>>
>> echo "1"> /sys/bus/platform/devices/neo1973-pm-bt.0/power_on
>> cat /sys/bus/platform/devices/neo1973-pm-bt.0/power_on
>> 0
>>
>> It says:
>>
>> neo1973-pm-bt neo1973-pm-bt.0: GTA02 Set PCF50633 LDO4 = 3200
>>
>> device never comes up. Can't I have a usb gadget and use bluetooth? I 
>> thought so. It would really be bad if I can't.
>>
>>
>
>