Kingston SDC4 don't work with OM2008.9's kernel

[Antonio Claudio Daniele Capobianco]

Happy new year to the community!
I have this SD, Kingston SDC4 (N0043-012.A00LF) an SDHC 4GB, but i can't use
with openmoko, because i have glamo errors!

I have tried to format e partitioning many times the SD, but with the same
outcome!
I have realized that the when i insert for the first time the SD in the
slot, openmoko succeeds in seeing the partitions, after a reboot i have this
errors and is impossibile to mount the partitions or to boot from SD!

I sorry for my English, i hope in the community help!

Using the comand dmesg i have in output this errors about the reading of the
SD (I've colored in red the errors )

root at om-gta02:~# dmesg
Linux version 2.6.24 (build at barbie) (gcc version 4.1.2) #1 PREEMPT Wed Dec
17 02:13:29 CST 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: GTA02
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
  DMA zone: 256 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 32512 pages, LIFO batch:7
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
CPU S3C2442B (id 0x32440aab)
S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: rootfstype=jffs2 root=/dev/mtdblock6
console=ttySAC2,115200 console=tty0 loglevel=8 regular_boot
mtdparts=physmap-flash:-(nor);neo1973-nand:0x00040000(u-boot),0x00040000(u-boot_env),0x00800000(kernel),0x000a0000(splash),0x00040000(factory),0x0f6a0000(rootfs)
irq: clearing pending ext status 000b02f0
irq: clearing pending ext status 000902d0
irq: clearing subpending status 00000087
irq: clearing subpending status 00000082
PID hash table entries: 512 (order: 9, 2048 bytes)
pclk = 50000000
timer_usec_ticks = 7864
timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
console [tty0] enabled
console [ttySAC2] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126080KB available (3304K code, 346K data, 128K init)
Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
modem wakeup interrupt
wake enabled for irq 17
wake enabled for irq 49
S3C2442: Initialising architecture
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c8800000, irq 33
DMA channel 1 at c8800040, irq 34
DMA channel 2 at c8800080, irq 35
DMA channel 3 at c88000c0, irq 36
S3C2442: Clock Support, DVS off
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pnp: the driver 'system' has been registered
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
s3c24xx_pwm s3c24xx_pwm.0: s3c24xx_pwm is registered
Enabling FIQ using irq 29
not changing prescaler of PWM 3, since it's shared with timer4 (clock tick)
NetWinder Floating Point Emulator V0.97 (double precision)
neo1973-version neo1973-version.0: starting
neo1973-pm-host neo1973-pm-host.0: starting
neo1973-resume neo1973-resume.0: starting
neo1973-memconfig neo1973-memconfig.0: starting
JFFS2 version 2.2. (NAND) (SUMMARY)  (c) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
glamo3362 glamo3362.0: Detected Glamo core 3650 Revision 0002 (49119232Hz
CPU / 81887232Hz Memory)
glamo3362 glamo3362.0: Glamo core now 49119232Hz CPU / 89980928Hz Memory)
Detected S-Media IRQ# pullup, enabling interrupt
glamo-spi-gpio glamo-spi-gpio.0: registering c03698a0: jbt6k74
SMEDIA Glamo frame buffer driver (C) 2007 Openmoko, Inc.
Console: switching to colour frame buffer device 80x58
fb0: SMedia Glamo frame buffer device
glamo-mci glamo-mci.0: glamo_mci driver (C)2007 Openmoko, Inc
glamo-mci glamo-mci.0: probe: mapped mci_base:c8864400 irq:0.
glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.
glamo-mci glamo-mci.0: initialisation done.
mmc_set_power(power_mode=1, vdd=20
physmap platform flash device: 00200000 at 18000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x0039
 Intel/Sharp Extended Query Table at 0x0039
 Intel/Sharp Extended Query Table at 0x0039
 Intel/Sharp Extended Query Table at 0x0039
 Intel/Sharp Extended Query Table at 0x0039
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x2000,blocks=8
erase region 1: offset=0x10000,size=0x10000,blocks=31
physmap-flash.0: 1 set(s) of 1 interleaved chips --> 4 partitions of 512 KiB
RedBoot partition parsing not available
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=0, 0ns Twrph0=3 30ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0xaa (Samsung NAND 256MiB 1,8V
8-bit)
s3c2410_nand_update_chip: chip c7d13eb8: 11
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 cmdlinepart partitions found on MTD device neo1973-nand
Creating 6 MTD partitions on "neo1973-nand":
0x00000000-0x00040000 : "u-boot"
0x00040000-0x00080000 : "u-boot_env"
0x00080000-0x00880000 : "kernel"
0x00880000-0x00920000 : "splash"
0x00920000-0x00960000 : "factory"
0x00960000-0x10000000 : "rootfs"
usbmon: debugfs is not available
usbcore: registered new interface driver libusual
s3c2410_udc: debugfs dir creation failed -19
s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes
gta02_udc_command(2)
mice: PS/2 mouse device common for all mice
input: Neo1973 Buttons as /devices/platform/neo1973-button.0/input/input0
wake enabled for irq 48
s3c2440-ts s3c2440-ts: successfully loaded
input: s3c2410 TouchScreen as /devices/virtual/input/input1
input: lis302-1 (top) as /devices/virtual/input/input2
lis302dl lis302dl.1: Found lis302-1 (top)
input: lis302-2 (bottom) as /devices/virtual/input/input3
lis302dl lis302dl.2: Found lis302-2 (bottom)
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
input: GTA02 PMU events as
/devices/platform/s3c2440-i2c/i2c-adapter/i2c-0/0-0073/input/input4
wake enabled for irq 53
pcf50633: dev (254:0)
pcf50633 0-0073: rtc core: registered pcf50633 as rtc0
pcf50633 0-0073: probe completed
neo1973-pm-bt neo1973-pm-bt.0: FIC Neo1973 Bluetooth Power Management:
starting
SD power -> 3200mV
glamo-mci glamo-mci.0: powered (vdd = 20) clk: 0kHz div=255 (req: 0kHz). Bus
width=0
glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
glamo-mci glamo-mci.0: Error after cmd: 0x8120
glamo-mci glamo-mci.0: Error after cmd: 0x120
glamo-mci glamo-mci.0: Error after cmd: 0x8120
glamo-mci glamo-mci.0: Error after cmd: 0x120
mmc_set_power(power_mode=2, vdd=15
SD power -> 2700mV
neo1973-pm-gps neo1973-pm-gps.0: FIC Neo1973 GPS Power Managerment:starting
APM Battery Driver
bq27000-battery bq27000-battery.0: BQ27000 Battery Driver (C) 2008 Openmoko,
Inc
power_supply bat: driver failed to report `status' property
S3c2440 SDIO Host controller
pnp: the driver 'sdio_s3c24xx_hcd' has been registered
mapped channel 0 to 0
S3c24xx SDIO: IRQ:37 Detect IRQ:0 DMA channel:0 base at 0xc9a00000 PCLK at 50000kHz
glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
sdio_s3c24xx_hcd 00:00: driver attached
sdio_s3c24xx_hcd 00:00: SDIO device, IDs SD_0008 (active)
pnp: the driver 'sdio_wlan' has been registered
Registered led device: neo1973:vibrator
Registered led device: gta02-power:orange
glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz).
Bus width=0
Registered led device: gta02-power:blue
glamo-mci glamo-mci.0: Error after cmd: 0x310
mmc_set_power(power_mode=0, vdd=0
Registered led device: gta02-aux:red
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.
mmc0: error -110 whilst initialising SD card
glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
pcf50633 0-0073: setting system clock to 2009-01-02 14:08:48 UTC
(1230905328)
CRCFAIL 0x1a3f
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 128K
CRCFAIL 0x1a3f
CRCFAIL 0x1a3f
sdio_wlan 00:01: driver attached
sdio_wlan 00:01: SDIO device, IDs SD_0001 (active)
BMI Get Target Info: Exit (ver: 0x20000059 type: 0x1)
SDIO_INT_CTRL enable IRQ
AR6000 Reg Code = 0x40000060
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk
usb0: MAC 06:ba:6e:96:48:e9
usb0: HOST MAC 76:f7:00:92:f0:58
usb0: RNDIS ready
gta02_udc_command(1)
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
NET: Registered protocol family 10
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
ASoC version 0.13.1
wm8753: WM8753 Audio Codec 0.16
asoc: WM8753 HiFi <-> s3c24xx-i2s mapping ok
asoc: WM8753 Voice <-> Bluetooth mapping ok
Only GTA01 hardware supported by ASoc driver
ADDRCONF(NETDEV_UP): usb0: link is not ready
mapped channel 10 to 2
usb0: full speed config #1: 500 mA, Ethernet Gadget, using CDC Ethernet
ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
usb0: no IPv6 routers present
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.openmoko.org/pipermail/openmoko-kernel/attachments/20090104/f7daafa2/attachment-0001.htm