Happy new year to the community!<br>I have this SD, Kingston SDC4 (N0043-012.A00LF) an SDHC 4GB, but i can't use with openmoko, because i have glamo errors!<br><br>I have tried to format e partitioning many times the SD, but with the same outcome! <br>
I have realized that the when i insert for the first time the SD in the slot, openmoko succeeds in seeing the partitions, after a reboot i have this errors and is impossibile to mount the partitions or to boot from SD!<br>
<br>I sorry for my English, i hope in the community help! <br><br>Using the comand dmesg i have in output this errors about the reading of the SD (I've colored in red the errors )<br><br>root@om-gta02:~# dmesg<br>Linux version 2.6.24 (build@barbie) (gcc version 4.1.2) #1 PREEMPT Wed Dec 17 02:13:29 CST 2008<br>
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177<br>Machine: GTA02<br>Memory policy: ECC disabled, Data cache writeback<br>On node 0 totalpages: 32768<br> DMA zone: 256 pages used for memmap<br> DMA zone: 0 pages reserved<br>
DMA zone: 32512 pages, LIFO batch:7<br> Normal zone: 0 pages used for memmap<br> Movable zone: 0 pages used for memmap<br>CPU S3C2442B (id 0x32440aab)<br>S3C244X: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz<br>
S3C24XX Clocks, (c) 2004 Simtec Electronics<br>CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on<br>CPU0: D VIVT write-back cache<br>CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets<br>CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets<br>
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512<br>Kernel command line: rootfstype=jffs2 root=/dev/mtdblock6 console=ttySAC2,115200 console=tty0 loglevel=8 regular_boot mtdparts=physmap-flash:-(nor);neo1973-nand:0x00040000(u-boot),0x00040000(u-boot_env),0x00800000(kernel),0x000a0000(splash),0x00040000(factory),0x0f6a0000(rootfs)<br>
irq: clearing pending ext status 000b02f0<br>irq: clearing pending ext status 000902d0<br>irq: clearing subpending status 00000087<br>irq: clearing subpending status 00000082<br>PID hash table entries: 512 (order: 9, 2048 bytes)<br>
pclk = 50000000<br>timer_usec_ticks = 7864<br>timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8<br>Console: colour dummy device 80x30<br>console [tty0] enabled<br>console [ttySAC2] enabled<br>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)<br>
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)<br>Memory: 128MB = 128MB total<br>Memory: 126080KB available (3304K code, 346K data, 128K init)<br>Calibrating delay loop... 199.47 BogoMIPS (lpj=498688)<br>Mount-cache hash table entries: 512<br>
CPU: Testing write buffer coherency: ok<br>net_namespace: 64 bytes<br>NET: Registered protocol family 16<br>S3C2410 Power Management, (c) 2004 Simtec Electronics<br>modem wakeup interrupt<br>wake enabled for irq 17<br>wake enabled for irq 49<br>
S3C2442: Initialising architecture<br>S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics<br>DMA channel 0 at c8800000, irq 33<br>DMA channel 1 at c8800040, irq 34<br>DMA channel 2 at c8800080, irq 35<br>DMA channel 3 at c88000c0, irq 36<br>
S3C2442: Clock Support, DVS off<br>Linux Plug and Play Support v0.97 (c) Adam Belay<br>usbcore: registered new interface driver usbfs<br>usbcore: registered new interface driver hub<br>usbcore: registered new device driver usb<br>
pnp: the driver 'system' has been registered<br>NET: Registered protocol family 2<br>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)<br>TCP established hash table entries: 4096 (order: 3, 32768 bytes)<br>
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)<br>TCP: Hash tables configured (established 4096 bind 4096)<br>TCP reno registered<br>s3c24xx_pwm s3c24xx_pwm.0: s3c24xx_pwm is registered <br>Enabling FIQ using irq 29<br>
not changing prescaler of PWM 3, since it's shared with timer4 (clock tick)<br>NetWinder Floating Point Emulator V0.97 (double precision)<br>neo1973-version neo1973-version.0: starting<br>neo1973-pm-host neo1973-pm-host.0: starting<br>
neo1973-resume neo1973-resume.0: starting<br>neo1973-memconfig neo1973-memconfig.0: starting<br>JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.<br>io scheduler noop registered<br>io scheduler deadline registered (default)<br>
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440<br>s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440<br>s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440<br>
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize<br>glamo3362 glamo3362.0: Detected Glamo core 3650 Revision 0002 (49119232Hz CPU / 81887232Hz Memory)<br>glamo3362 glamo3362.0: Glamo core now 49119232Hz CPU / 89980928Hz Memory)<br>
Detected S-Media IRQ# pullup, enabling interrupt<br>glamo-spi-gpio glamo-spi-gpio.0: registering c03698a0: jbt6k74<br>SMEDIA Glamo frame buffer driver (C) 2007 Openmoko, Inc.<br>Console: switching to colour frame buffer device 80x58<br>
fb0: SMedia Glamo frame buffer device<br>glamo-mci glamo-mci.0: glamo_mci driver (C)2007 Openmoko, Inc<br>glamo-mci glamo-mci.0: probe: mapped mci_base:c8864400 irq:0.<br>glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.<br>
glamo-mci glamo-mci.0: initialisation done.<br>mmc_set_power(power_mode=1, vdd=20<br>physmap platform flash device: 00200000 at 18000000<br>physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank<br> Intel/Sharp Extended Query Table at 0x0039<br>
Intel/Sharp Extended Query Table at 0x0039<br> Intel/Sharp Extended Query Table at 0x0039<br> Intel/Sharp Extended Query Table at 0x0039<br> Intel/Sharp Extended Query Table at 0x0039<br>cfi_cmdset_0001: Erase suspend on write enabled<br>
erase region 0: offset=0x0,size=0x2000,blocks=8<br>erase region 1: offset=0x10000,size=0x10000,blocks=31<br>physmap-flash.0: 1 set(s) of 1 interleaved chips --> 4 partitions of 512 KiB<br>RedBoot partition parsing not available<br>
S3C24XX NAND Driver, (c) 2004 Simtec Electronics<br>s3c2440-nand s3c2440-nand: Tacls=0, 0ns Twrph0=3 30ns, Twrph1=2 20ns<br>NAND device: Manufacturer ID: 0xec, Chip ID: 0xaa (Samsung NAND 256MiB 1,8V 8-bit)<br>s3c2410_nand_update_chip: chip c7d13eb8: 11<br>
Bad block table found at page 131008, version 0x01<br>Bad block table found at page 130944, version 0x01<br>6 cmdlinepart partitions found on MTD device neo1973-nand<br>Creating 6 MTD partitions on "neo1973-nand":<br>
0x00000000-0x00040000 : "u-boot"<br>0x00040000-0x00080000 : "u-boot_env"<br>0x00080000-0x00880000 : "kernel"<br>0x00880000-0x00920000 : "splash"<br>0x00920000-0x00960000 : "factory"<br>
0x00960000-0x10000000 : "rootfs"<br>usbmon: debugfs is not available<br>usbcore: registered new interface driver libusual<br>s3c2410_udc: debugfs dir creation failed -19<br>s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes<br>
gta02_udc_command(2)<br>mice: PS/2 mouse device common for all mice<br>input: Neo1973 Buttons as /devices/platform/neo1973-button.0/input/input0<br>wake enabled for irq 48<br>s3c2440-ts s3c2440-ts: successfully loaded<br>
input: s3c2410 TouchScreen as /devices/virtual/input/input1<br>input: lis302-1 (top) as /devices/virtual/input/input2<br>lis302dl lis302dl.1: Found lis302-1 (top)<br>input: lis302-2 (bottom) as /devices/virtual/input/input3<br>
lis302dl lis302dl.2: Found lis302-2 (bottom)<br>i2c /dev entries driver<br>s3c2440-i2c s3c2440-i2c: slave address 0x10<br>s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz<br>s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter<br>
input: GTA02 PMU events as /devices/platform/s3c2440-i2c/i2c-adapter/i2c-0/0-0073/input/input4<br>wake enabled for irq 53<br>pcf50633: dev (254:0)<br>pcf50633 0-0073: rtc core: registered pcf50633 as rtc0<br>pcf50633 0-0073: probe completed<br>
neo1973-pm-bt neo1973-pm-bt.0: FIC Neo1973 Bluetooth Power Management: starting<br>SD power -> 3200mV<br>glamo-mci glamo-mci.0: powered (vdd = 20) clk: 0kHz div=255 (req: 0kHz). Bus width=0<br>glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br>
glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br>glamo-mci glamo-mci.0: powered (vdd = 20) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br><span style="color: rgb(255, 0, 0);">glamo-mci glamo-mci.0: Error after cmd: 0x8120</span><br style="color: rgb(255, 0, 0);">
<span style="color: rgb(255, 0, 0);">glamo-mci glamo-mci.0: Error after cmd: 0x120</span><br style="color: rgb(255, 0, 0);"><span style="color: rgb(255, 0, 0);">glamo-mci glamo-mci.0: Error after cmd: 0x8120</span><br style="color: rgb(255, 0, 0);">
<span style="color: rgb(255, 0, 0);">glamo-mci glamo-mci.0: Error after cmd: 0x120</span><br>mmc_set_power(power_mode=2, vdd=15<br>SD power -> 2700mV<br>neo1973-pm-gps neo1973-pm-gps.0: FIC Neo1973 GPS Power Managerment:starting<br>
APM Battery Driver<br>bq27000-battery bq27000-battery.0: BQ27000 Battery Driver (C) 2008 Openmoko, Inc<br>power_supply bat: driver failed to report `status' property<br>S3c2440 SDIO Host controller<br>pnp: the driver 'sdio_s3c24xx_hcd' has been registered<br>
mapped channel 0 to 0<br>S3c24xx SDIO: IRQ:37 Detect IRQ:0 DMA channel:0 base@0xc9a00000 PCLK@50000 kHz<br>glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br>glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br>
glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br>sdio_s3c24xx_hcd 00:00: driver attached<br>sdio_s3c24xx_hcd 00:00: SDIO device, IDs SD_0008 (active)<br>pnp: the driver 'sdio_wlan' has been registered<br>
Registered led device: neo1973:vibrator<br>Registered led device: gta02-power:orange<br>glamo-mci glamo-mci.0: powered (vdd = 15) clk: 195kHz div=255 (req: 195kHz). Bus width=0<br>Registered led device: gta02-power:blue<br>
<span style="color: rgb(255, 0, 0);">glamo-mci glamo-mci.0: Error after cmd: 0x310</span><br>mmc_set_power(power_mode=0, vdd=0<br>Registered led device: gta02-aux:red<br>usbcore: registered new interface driver hiddev<br>
usbcore: registered new interface driver usbhid<br>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver<br>glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.<br><span style="color: rgb(255, 0, 0);">mmc0: error -110 whilst initialising SD card</span><br>
glamo-mci glamo-mci.0: glamo_mci_set_ios: power down.<br>TCP cubic registered<br>NET: Registered protocol family 1<br>NET: Registered protocol family 17<br>RPC: Registered udp transport module.<br>RPC: Registered tcp transport module.<br>
pcf50633 0-0073: setting system clock to 2009-01-02 14:08:48 UTC (1230905328)<br>CRCFAIL 0x1a3f<br>VFS: Mounted root (jffs2 filesystem).<br>Freeing init memory: 128K<br>CRCFAIL 0x1a3f<br>CRCFAIL 0x1a3f<br>sdio_wlan 00:01: driver attached<br>
sdio_wlan 00:01: SDIO device, IDs SD_0001 (active)<br>BMI Get Target Info: Exit (ver: 0x20000059 type: 0x1)<br>SDIO_INT_CTRL enable IRQ<br>AR6000 Reg Code = 0x40000060<br>ether gadget: using random self ethernet address<br>
ether gadget: using random host ethernet address<br>usb0: Ethernet Gadget, version: May Day 2005<br>usb0: using s3c2410_udc, OUT ep2-bulk IN ep1-bulk STATUS ep3-bulk<br>usb0: MAC 06:ba:6e:96:48:e9<br>usb0: HOST MAC 76:f7:00:92:f0:58<br>
usb0: RNDIS ready<br>gta02_udc_command(1)<br>Bluetooth: Core ver 2.11<br>NET: Registered protocol family 31<br>Bluetooth: HCI device and connection manager initialized<br>Bluetooth: HCI socket layer initialized<br>Bluetooth: HCI USB driver ver 2.9<br>
usbcore: registered new interface driver hci_usb<br>Bluetooth: L2CAP ver 2.9<br>Bluetooth: L2CAP socket layer initialized<br>Bluetooth: HIDP (Human Interface Emulation) ver 1.2<br>NET: Registered protocol family 10<br>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver<br>
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI<br>s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1<br>s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000<br>usb usb1: configuration #1 chosen from 1 choice<br>
hub 1-0:1.0: USB hub found<br>hub 1-0:1.0: 2 ports detected<br>Bluetooth: RFCOMM socket layer initialized<br>Bluetooth: RFCOMM TTY layer initialized<br>Bluetooth: RFCOMM ver 1.8<br>ASoC version 0.13.1<br>wm8753: WM8753 Audio Codec 0.16<br>
asoc: WM8753 HiFi <-> s3c24xx-i2s mapping ok<br>asoc: WM8753 Voice <-> Bluetooth mapping ok<br>Only GTA01 hardware supported by ASoc driver<br>ADDRCONF(NETDEV_UP): usb0: link is not ready<br>mapped channel 10 to 2<br>
usb0: full speed config #1: 500 mA, Ethernet Gadget, using CDC Ethernet<br>ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready<br>usb0: no IPv6 routers present<br><br><br><br>