flash.sh failed when setup qemu-neo1973

孙廉焘 sunliantao at gmail.com
Wed Oct 31 09:03:05 CET 2007


Hi all,

I have a problem, when I setup the qemu-neo1973 envirement followed by
http://wiki.openmoko.org/wiki/Qemu.

I have done these steps:
sudo apt-get install netpbm lynx
svn checkout https://svn.openmoko.org/trunk/src/host/qemu-neo1973
cd qemu-neo1973
 ./configure --target-list=arm-softmmu --cc=/home/sunlt/gcc33
 make
openmoko/download.sh
openmoko/flash.sh

After openmoko/flash.sh, the output information is listed briefly as
following(full version is an attachment):

ls: /root/openmoko/qemu-neo1973/openmoko/uImage-2.6.*-neo1973.bin: No
such file or directory
U-Boot 1.2.0-moko9_r0 (Aug 19 2007 - 19:17:12)
 DRAM:  128 MB
 NAND:  Bad block table not found for chip 0
 Bad block table not found for chip 0
 64 MiB
 *** Warning - bad CRC or NAND, using default environment
Creating BBT. Please wait ...Bad block table not found for chip 0
Bad block table not found for chip 0
Bad block table written to 0x03ffc000, version 0x01
Bad block table written to 0x03ff8000, version 0x01

GTA01Bv4 # setenv bootcmd 'setenv bootargs ${bootargs_base}
${mtdparts}; bootm 0x31000000'
GTA01Bv4 # setenv menu_1 'Set console to USB: setenv stdin usbtty;
setenv stdout usbtty; setenv stderr usbtty'
GTA01Bv4 # setenv menu_2 'Set console to serial: setenv stdin serial;
setenv stdout serial; setenv stderr serial'
GTA01Bv4 # setenv menu_3 'Power off: neo1973 power-off'
GTA01Bv4 # setenv splashimage 'nand read.e 0x36000000 splash 0x5000;
unzip 0x36000000 0x33d00000 0x96000'
GTA01Bv4 # setenv mtdids nand0=neo1973-nand
GTA01Bv4 # setenv mtdparts
mtdparts=neo1973-nand:0x00050000(u-boot),0x00004000(u-boot_env),0x00208000(kernel),0x00010000(splash),0x039a4000(rootfs)
GTA01Bv4 # #dynpart
Unknown command '#dynpart' - try 'help'
GTA01Bv4 # nand write.e 0x31000000 u-boot 0x33660

NAND write: device 0 offset 0x0, size 0x33660

Writing data at 0x33600 -- 100% complete.

Erasing Nand...Writing to Nand... done
GTA01Bv4 # neo1973 power-off
poweroff
pcf_write: Power-off requested.
openmoko/flash.sh: line 114: 30382 已终止               ( sleep $2; kill
$pid; sleep 1; kill -KILL $pid )  (wd: /root/openmoko/qemu-neo1973)
Please wait, programming the NAND flash...
neo_gsm_switch: GSM disabled.

pcf_write: Power-off requested.
Please wait, programming the NAND flash...
sleep: invalid time interval 'nand'
sleep: invalid time interval 'write.e'
sleep: invalid time interval 'kernel'
For more information, try 'sleep --help'
openmoko/flash.sh: line 88: 30385 terminaled               ( sleep $2;
kill $pid; sleep 1; kill -KILL $pid )
openmoko/flash.sh: line 88: 30387 terminaled               $qemu
-mtdblock "$script_dir/$flash_base" -kernel "$script_dir/$1" -serial
stdio -nographic -usb -monitor null 0<&0

U-boot failed to finish writing in nand write.e 0x31000000 kernel
0x1000 seconds, giving up.

Who can help me?
Thank you very much!

sytax
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Output-of-flash.sh
Type: application/x-sh
Size: 5614 bytes
Desc: not available
Url : http://lists.openmoko.org/pipermail/community/attachments/20071031/460f1029/attachment.sh 


More information about the community mailing list