2.6.37 (qtmoko-v32.1 test report)

[Timo Juhani Lindfors]

Hi Lars and Radek,

Radek Polak <psonek2 at seznam.cz> writes:
> I have now ported most of 2.6.34 patches from my qtmoko git on to of this. The 
> repository is here [1].

thanks a lot for your efforts! Here's a preliminary test report. I'm
running qtmoko-v32.1 branch

$ git log --oneline om-2.6.37..qtmoko-v32.1
84af470 Revert input version as tslib compiled against older
c90c0d0 GTA02 config - bump version to v32
d366e03 GTA02 config - compile new battery driver
0a3c7cf GTA02 config - regenerate for 2.6.37
a849cbc GTA02 config from qtmoko-v31 (2.6.34 based)
ff44a38 Use 100 as HZ value on S3C24XX
4e6ab66 wm8753: use snd_soc_jack on neo1973
b6f1cb1 Force GPS power up on resume if it were powered up on suspend
1bb67b1 s3c2410_ts: jitter less touchscreen for glamo, version 4
71e0285 Openmoko resume reason sysfs node ported from 2.6.29
efcd40e Rename /dev/s3c2410_serialXXX to /dev/ttySACXXX
5a6bd71 glamo-display: fix WSOD for 242 timming
373c7d7 Enable powering off after 8s POWER press
64929b7 Fix high power consumption in suspend
3c96492 tslib relies on ts pressures events so this hack is needed to get tslib stuff working
4ec5000 ar6000_delay.patch
a29b83e usbhost.patch
0756a5e touchscreen: ignore unexpected interrupts
4b9b0a2 wm8753: fix build with gcc-4.4.2, which works ok with 4.1.2

with a few extra patches:

$ git log --oneline qtmoko-v32.1..lindi-qtmoko-v32.1
ba97d73 remove -v32 localversion
c7064e8 Port ramconsole patch to 2.6.34
d44c1e2 Add CONFIG_OPENMOKO_RESUME_REASON=m
b36cab3 add symlink to config

and u-boot stable branch with a few extra patches:

$ git log --oneline stable..lindi
5328070 bugfix previous patch, enable watchdog only for resume, not boot
47e4c33 buildfix previous patch
abb1f1c experiment: explicitely start watchdog on boot/resume
cc1e94f experiment: do not disable watchdog on boot/resume
9c2b2be Do power on LDO5 (GPS) regulator and do not setup all serial's GPIOs at all on boot
d4a3860 Kindly ask u-boot do not touch serials and serial's gpio setup
4ae4060 Turn vibrator on and aux off on resume.
f4cd104 Add support for forcing charging at maximum current (usually 500 mA). This is useful if the battery is fully depleted and one wants to stay in the boot loader waiting for the battery to charge.

First I tested all features offered by omhacks. I noticed the
following problems:

1) om screen resolution

does not work since

/sys/devices/platform/s3c2440-i2c/i2c-adapter/i2c-0/0-0073/pcf50633-regltr.9/glamo3362.0/glamo-spi-gpio.0/spi2.0/state

does not exist. Is there some other sysfs node for toggling between qvga and vga?

2) om battery charger-limit

does not work since neither

/sys/class/i2c-adapter/i2c-0/0-0073/pcf50633-mbc/chg_curlim

nor

/sys/devices/platform/s3c2440-i2c/i2c-0/0-0073/pcf50633-mbc/chg_curlim

exists. Is the fix just to use

/sys/devices/platform/s3c2440-i2c/i2c-0/0-0073/pcf50633-mbc.0/chg_curlim?

Could we make these patches more stable somehow?

3) huawei 3G dongle does not switch to modem mode:

Jan  8 15:54:59 ginger kernel: [ 1751.490000] usb 1-2: new full speed USB device using s3c2410-ohci and address 39
Jan  8 15:54:59 ginger kernel: [ 1751.670000] usb 1-2: New USB device found, idVendor=12d1, idProduct=1001
Jan  8 15:54:59 ginger kernel: [ 1751.670000] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=1
Jan  8 15:54:59 ginger kernel: [ 1751.670000] usb 1-2: Product: HUAWEI Mobile
Jan  8 15:54:59 ginger kernel: [ 1751.670000] usb 1-2: Manufacturer: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
Jan  8 15:54:59 ginger kernel: [ 1751.670000] usb 1-2: SerialNumber: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
Jan  8 15:54:59 ginger kernel: [ 1751.900000] usbcore: registered new interface driver ub
Jan  8 15:54:59 ginger kernel: [ 1752.340000] SCSI subsystem initialized
Jan  8 15:55:00 ginger kernel: [ 1752.540000] Initializing USB Mass Storage driver...
Jan  8 15:55:00 ginger kernel: [ 1752.540000] usbcore: registered new interface driver usb-storage
Jan  8 15:55:00 ginger kernel: [ 1752.540000] USB Mass Storage support registered.
$ ls -l /dev/ttyUSB*
ls: cannot access /dev/ttyUSB*: No such file or directory

Adding "option" to /etc/modules fixed this -- should it get loaded
automatically? Even after that

Jan  8 15:59:45 ginger kernel: [ 2037.460000] usbcore: registered new interface driver usbserial
Jan  8 15:59:45 ginger kernel: [ 2037.460000] USB Serial support registered for generic
Jan  8 15:59:45 ginger kernel: [ 2037.460000] usbcore: registered new interface driver usbserial_generic
Jan  8 15:59:45 ginger kernel: [ 2037.460000] usbserial: USB Serial Driver core
Jan  8 15:59:45 ginger kernel: [ 2037.650000] USB Serial support registered for GSM modem (1-port)
Jan  8 15:59:45 ginger kernel: [ 2037.650000] usbcore: registered new interface driver option
Jan  8 15:59:45 ginger kernel: [ 2037.650000] option: v0.7.2:USB Driver for GSM modems

I get no /dev/ttyUSB*.

4) om usb charger-limit

does not work since

/sys/class/i2c-adapter/i2c-0/0-0073/pcf50633-mbc/usb_curlim

does not exist. Should I again use

/sys/devices/platform/s3c2440-i2c/i2c-0/0-0073/pcf50633-mbc.0/usb_curlim

instead?

5) udev rule

SUBSYSTEM=="input", ATTRS{name}=="lis302-1 (top)", SYMLINK+="accelerometer-top"

does not find accelerometers. No node in /dev/input seems to be an
accelerometer.

6) (as I reported earlier) when I touch the screen to wake it up from
dpms sleep I see white screen for a few milliseconds. I'm using
xserver-xorg-video-fbdev.